欢迎您来到全球机械网! 请登陆 免费注册

关注我们

经典浸锡工艺的漂洗助剂

产品价格
面议
发布日期
2023年5月26日
联系人
方女士-中镀科技
手机号码
18962647161
固定电话
联系我时,请说是在全球机械网上看到的哦!
  • 详情
ORMECON RAD 7000 C是一种水性,碱性,液体浓缩物,用于在ORMECON CSN 7004浸泡锡槽初始水冲洗后协助去除PCB(印刷电路板)上的残留物。当用去离子水稀释时,ORMECON RAD 7000 C可以中和浸泡锡槽中留在PCB上的酸性残留物,显著降低电路板上的离子污染水平。它可以用于喷雾或浸泡应用。ORMECON RAD 7000 C是免费漂洗,完全兼容整个系列的CSN经典lmmersion锡工艺化学。
OPERATING CONDITIONS【操作参数】
Horizontal Range Nominal
Concentration(浓度) 1.0 to 25% by volume 5.0%
Temperature (温度) 40 to 60 C (104 to 140°F) 50°C (122 °F)

MAKE-UP PROCEDURE【组成】
Before handling any of the products referred to in this data sheet ensure all relevant Safety Data Sheets have been read and understood. 在处理本数据表中提到的任何产品之前,确保已阅读和理解所有相关的安全数据表。
To make up the ORMECON RAD 7000 Post Treatment Rinse Aid add the required amount of ORMECONRAD 7000 C to heated, recirculating, water. 为配制ORMECONRAD 7000处理后漂洗助剂,将所需量的ORMECONRAD 7000 C加入加热的循环水中。
OPERATION【操作】
PCB panels must be thoroughly rinsed with Dl water prior to entering the ORMECON RAD 7000 C rinse aid.DO NOT use ORMECON RAD 7000 C immediately following ORMECON 7004 CSN immersion tin bath without a water rinse. Typical dwell times in ORMECON RAD 7000C are between 20 and 90 seconds. ORMECON RAD 7000 C is always followed by thorough water rinsing to ensure removal of the rinse aid solution from the PCB board surface. Deionized water should be used in the final rinse to achieve the required ionic cleanliness. ORMECON RAD7000 C treatment is especially recommended for complex board designs, as well as blind vias and solder mask plugged holes. 在进入ORMECON RAD 7000 C冲洗助剂之前,PCB板必须用Dl水彻底冲洗。在没有水冲洗的情况下,不要在ORMECON 7004 CSN浸泡锡浴后立即使用ORMECON RAD 7000c。ORMECON RAD 7000C的典型停留时间在20到90秒之间。ORMECON RAD 7000 C清洗后必须进行彻底的水冲洗,以确保PCB板表面的漂洗辅助溶液被清除。后冲洗时应使用去离子水,以达到所需的离子清洁度。ORMECON RAD7000 C处理特别推荐用于复杂的电路板设计,以及盲孔和阻焊塞孔。
EQUIPMENT REQUIRED 【设备要求】
ORMECON RAD 7000 C working solutions may be contained in stainless steel, polypropylene, and PTFE. Heaters may be of PTFE ,PTFE coated stainless steel or titanium. lt is recommended that heaters are supplied with over temperature shut off protection. ORMECON RAD 7000 C工作溶液可能含有不锈钢、聚丙烯和聚四氟乙烯。加热器可以是聚四氟乙烯,聚四氟乙烯涂层不锈钢或钛。建议加热器提供超温关闭保护。
Exhaust ventilation is required to remove fumes or mist that may be generated during make-up and operation.排气通风是必要的,以清除在装配和操作过程中可能产生的烟雾或薄雾。
CONTROL【控制】
The following analytical procedure is recommended for use by personnel who have been trained to use laboratory practices which are considered safe and prudent by chemical industry standards. Such practices include suitable personal protective equipment, the use of proper equipment, the use of proper methods of handling all chemicals and proper laboratory procedures. Use only analytical reagent grade chemicals and deionized or distilled water in the following analytical procedures. 以下分析程序建议由经过化学工业标准认为安全谨慎的实验室操作培训的人员使用。这些做法包括适当的个人防护装备、使用适当的设备、使用适当的方法处理所有化学品和适当的实验室程序。在以下分析程序中,仅使用分析试剂级化学品和去离子水或蒸馏水。
CAUTION:注意事项 The following procedures involve the use of potentially hazardous chemicals. Consult manufacturer's Safety Data Sheets and follow the appropriate safety precautions. 以下程序涉及到潜在危险化学品的使用。查阅制造商的安全数据表,并遵循适当的安全预防措施。
ANALYSIS METHOD OF WORKING SOLUTION【分析方法】
Equipment Needed设备要求
Pipette(移液管): 5.0 mL
Conical Flask(锥形烧瓶): 250 mL
Reagents Needed试剂要求
0.1 mol/L HCl
Phenolphthalein Indicator Solution(酚酞指示剂): Phenolphthalein 0.1g, Dl water 30 mL, and Ethanol 70 mL酚酞0.1g, Dl水30 mL,乙醇70 mL。
Procedure过程
1.Pipet 5mL of sample into the conical flask.用移液管取 5mL样品放入锥形瓶中。
2. Add 100 to 150mL of Dl water. 加入100至150mL Dl水。
3.Add 5 to 10 drops of Phenolphthalein indicator solution. 加入5 - 10滴酚酞指示剂溶液。
4.Titrate with 0.1 mol/L HCl from purple to colorless end point . 用0.1 mol/L HCl滴定,从紫色终点至无色终点。
Calculation计算
RAD7000 C (%)= vol of HCl (mL)x 0.177 x Factor
(For 0.1mol/l HCl, the Factor =1)
Replenishment补充
The concentration of ORMECON RAD 7000 C working solution can be maintained with additions of the ORMECON RAD 7000 C concentrate. An addition of 10 ml of ORMECON RAD 7000 C to 1 L of working solution will raise the ORMECON RAD 7000 C concentration by 1%.通过添加ORMECON RAD 7000 C浓缩物,可以保持ORMECON RAD 7000 C工作溶液的浓度。在1 L的工作溶液中加入10 ml的ORMECON RAD 7000 C,可以使ORMECON RAD 7000 C浓度提高1%。
RECOMMENDED BATH LIFE FOR【推荐槽液寿命】
Under typical mass production conditions, the ORMECON RAD 7000 C bath should be replaced every four weeks. 在典型的大规模生产条件下,ORMECON RAD 7000 C浴槽应每四周更换一次。
HANDLING AND SAFETY INSTRUCTIONS【操作安和全说明】
For detailed information consult the material safety data sheets for this product. 有关详细信息,请参阅本产品的材料安全数据表.
Please read material safety data sheets carefully before using this product.使用本产品前,请仔细阅读材料安全数据表。
DISCLAIMER【特别声明】
All recommendations and suggestions in this bulletin concerning the use of our products are based upon tests and data believed to be reliable. Since the actual use by others is beyond our control, no guarantee expressed or implied, is made by our company , as to the effects of such use or results to be obtained, nor is any information to be construed as a recommendation to infringe any patent.
此说明书内所有提议或建议,是以本公司信赖的实验及资料为基础。因不能控制其他从业者的实际操作,故本公司不能保证及负责任何不良后果。此说明书内的所有资料也不能用为侵犯版权的证据

询价留言

  • *
  • *
  • *

免责声明

  • 以上信息(包括文字、图片、视频等)由用户自行提供,该用户负责信息内容的真实性、准确性和合法性。全球机械网不提供任何保证,并不承担任何法律责任。 全球机械网提醒您交易小心谨慎。

商家档案

最新产品更多