6YL-120型螺旋榨油机

6YL---120型螺旋榨油机

MODEL6YL---120 SCREW OIL PRESS

一．主要性能参数:

Main Specifications

1,榨轴转速:45-55转/分

Shaft speed:45-55r/m

2,齿轮箱传动比:15/34×13/55=1:9.59

Gear ratio in gearbox: 15/34×13/55=1:9.59

3配用动力:11KW

Motor:11KW

4三角带:B型

Belt: B型

5外形尺寸:长x宽x高1820x570x1320(mm)

Outer dimension: L×W×H(mm) 1820x570x1320

6单机重量:760kg

Weight:580kg

7生产能力见表(一)

Capacity see table (1)

Table(1)production capacity



油料名称

raw material

每24小时处理量(吨)

feeding per hour(t)

每百公斤产油量(kg)Oil output per 100kg raw material

干饼残油率(%)

residue(%)



菜籽

rape seeds

热榨

Hot pressing

6-7

30-38

7.5-8

冷榨

Cold pressing

3-5

28-35





花生

Ground nuts

热榨

Hot pressing

6-7

35-45

7

冷榨

Cold pressing

3-3.5

32-40





大豆

Bean

热榨

Hot pressing

5-6

10-16

6.5-7

冷榨

Cold pressing

.3-3.5

8-14



芝麻

sesame

热榨

Hot pressing

6-7

44-47

6.5-7.5

棉籽

Cotton seeds

冷榨

Cold pressing

3-4

10-14

5.5-6.5

注：以上参数是指清选，分离，轧胚辅助设备齐全，工艺合理，操作正常是能达到指标。

Note ： Figures shown above reflect performance when selecting ，separating，auxiliary facilities are available when manufacturing is rational.

二,工作原理与构造:

1,工作原理:

榨油机运转时,将处理好的料胚带如料斗,油料从料斗进入榨膛。有榨螺的螺旋向里推进，进行压榨。

因料胚在榨油机的榨膛内是在运转状态下进行的，在榨膛高压的条件下，料胚和榨膛之间产生很大的摩擦阻力。这样就能使料胚和料胚产生摩擦，造成相对的运动。另一放面，榨螺的根圆直径是逐渐增粗的，当榨螺转动时，螺纹使料胚即能向前推进又能向外翻转，同时靠近榨螺螺纹表面的料层随着榨轴转动，这样在榨膛里的每个料胚微粒都不是等速度同方向的运动。而在微粒之间也存在着相对的运动。有摩擦产生的热量又满足了榨油工艺操作上所必须的一份热量，有助于促使料胚中的蛋白质热变性，破坏了胶体，增加了塑性，同时也降低了油的粘性，容易析```````榨出油来，因而提高了榨油机的出油率。

2， Oration principle and structure

2.1 oration principle

When oil presses operating prepared material enters extruding chamber from the hopper and then moves forwards by the rotating pressing screw and is pressed. Under the high-pressure condition in the chamber ,friction between material and screw ,between material and chamber will be created ,which also creates friction and relative movement among material particles. On the other hand, root diameter of the pressing screw caries larger from one end to the other ,hence. When rotating ,it not only pushes particles moving forwards but turns them outwards as well ,meanwhile ,particles adjacent the screw will rotation along with screw’ rotating ,causing every particle inside the chamber to possess different speed. Therefore relative movement among particle creates heat which is necessary during manufacturing because of helping protein change property ,damage colloid ,increase plasticity ,decrease oil’s elasticity ,resulting in high oil productivity.

2．结构：该机有进料斗部分，齿轮箱部分，榨膛部分，榨螺部分，机架部分共五大部分组成：见图（一）



图一



三．机器的安装：

榨油机安装时必须在地脚螺栓牢固的安装基础上，使机体保持水平。电机安在进料斗的背面。

3．Installment

The oil press must be installed by bolts firmly on the foundation and be kept horizontal

四．机器的润滑：

1．榨油机主要采用机油和黄油两种形式润滑。加油周期见表二

序号

NO

润滑部位

lubrication

油脂种类

lubricate

加油周期

Time span

换油周期

Lubricate replacement period

1

调节螺栓

Adjusting bolt

20号机械油

Mechanical oil NO.20

每班2次

1-2time/day



2

伞齿轮

Bevel gear

20号机械油Mechanical oil NO.20

每班2次

1-2time/day



3

轴承座套

Bearing bush

20号机械油Mechanical oil NO.20

每班2次

1-2time/day



4

齿轮箱

Gearbox

20号机械油Mechanical oil NO.20

首次加油12kg

First time 12kg

六个月

Every 6 months

5

各滚动轴承

bearing

润滑油

grease



每年一次

Each year

4.Lubrication

4.1 Oil press is lubricated by lubricating oil and grease, see table(2)

五.机器操作:

(一)开机前的要点:

1.开机前先将齿轮箱内加注12公斤机油.

2机器安装好后,按规定加注润滑油,检查各零部件是否紧固,操作手柄,插板是否灵活.

3.用手搬动大皮带轮查机器有无松动或卡机现象,若有异常及时排除.

4.调整皮带的松紧度,启动电机,检查槽轮方向是否与标志方向一致.

5检查准备工作做好后,松开紧锁螺母把榨螺拧到死点,再退回3-4圈,再前进半圈,保证榨螺与出饼口的间隙.

5.1 preparation before operating

5.1.1 12kg of lubricant needs to be filled into the gearbox.

5.1.2 After installing the machine, check whether lubricant has been filled in, bolts have been tightened, and handles are operable.

5.1.3 Check large pulley whether it is loose or blocked ,repair it if necessary.

5.1.4 Adjust the tightness of the belt ,switch on the motor and check its rotation direction.

5.1.5 Loosen the lock nut and tighten the screw to its end, then loose it for3-4circles and then tighten it again for half circle to assure the gap of the residue cake outlet.

(二)开机:

1,启动电机,开动机器,将饼加入6%-8%水分,倒入料斗,磨光榨膛,进料不可过猛,否则可能造成榨膛堵塞与卡死机器事故,因此开始下料应该缓慢均匀,待榨膛磨光后,正常出饼后,方可将料胚倒入料斗.

2.运转后观察出饼情况,如不出饼,将榨螺再退出1-2圈,如还不出饼,应停机检查.切记杜绝开带车.故障排除后再行初榨工作.正常运转时饼厚1-2毫米,饼成瓦片状,手捏不粘,内面光滑,外面发皱,表面不带油迹.

饼厚的调节:搬动调节螺旋上的手柄,将调节螺栓顺时针旋转,螺栓往外,饼就厚,反之饼就薄了。（调节螺栓为左T165x6）出饼圈与出渣稍头的锥角不同，每转一圈较饼厚度变化为0.4-0.5毫米。

3．榨油机运转中，应经常检查出油，出渣情况，正常时油大部分从条排与前几节园排流出。如饼碎成渣，说明胚料太干。如发现饼发热（散出蒸汽）成大片状说明水分太高，应及时进行调节胚料水分的含量。

出渣：条排出渣时成细片状说明水分高，如出粉状含沫说明水分低。园排渣过多属压紧螺母未压紧圆排，应上紧压紧螺母，如水分合适，则条排不出渣或少出渣，圆排少量出渣也是允许的。料胚含水分的高低直接影响出油率，因此压榨时应控制好料胚的水分。